C DX-10
Natural Sound Compact Disc Player
Lecteur de disque audionumérique de la série “Natural Sound”
Thank you for selecting this YAMAHA Compact Disc Player.
Nous vous remercions d’avoir porté votre choix sur ce lecteur de disque.
OWNER’S MANUAL
MODE D’EMPLOI
FEATURES
CARACTERISTIQUES
Lecture programmable à accès direct
Lecture en séquence aléatoire
Lecture répétée de plage unique/disque entier
Fonction d’espacement automatique
Programmation automatique de pour
l’enregistrement
•
•
•
•
•
Random Access Programmable Play
Random-Sequence Play
Single Track/Entire Disc Repeat Play
Automatic Spacing Capability
Automatic Programming for Recording to
Tape
•
•
•
•
•
Fonction de recherche automatique du niveau
de crête
•
•
• Automatic Peak Level Searching Capability
• CD Synchronized Recording with a
Compatible YAMAHA Tape Deck
Enregistrement synchronisé de disque
audionumérique avec un magnétophone à
cassettes compatible YAMAHA
Fonction de modification de luminosité de
l’affichage
Fonctionnement par télécommande
Sortie numérique optique
Display Brightness Changing Capability
Remote Control Capability
•
•
•
•
Optical Digital Output
•
•
CONTENTS
TABLE DES MATIERES
Safety Instructions ............................................... 2
Connections......................................................... 4
Identification of Components ............................... 5
Basic Operation ................................................... 7
Random-Sequence Play.................................... 10
Repeat Play ....................................................... 10
Program Play ..................................................... 11
Index Search...................................................... 12
Track Programming for Recording to Tape ....... 13
CD Synchronized Recording ............................. 17
Notes about the Remote Control
Attention ............................................................. 20
Connexions ......................................................... 21
Identification des composants ............................ 22
Fonctionnement de base .................................... 24
Lecture en séquence aléatoire ........................... 27
Lecture repetée .................................................. 27
Lecture programmée .......................................... 28
Recherche d’index .............................................. 29
Programmation des plages pour
enregistrement sur bande .................................... 30
Enregistrement synchronise d’un
disque audionumérique ........................................34
Remarques concernant la télécommande .......... 35
Remarques concernant la manipulation des disques ... 35
Dépistage de pannes .......................................... 36
Caractéristiques techniques ............................... 36
Transmitter ......................................................... 18
Notes about Handling Compact Discs ............... 18
Troubleshooting.................................................. 19
Specifications..................................................... 19
CAUTION: READ THIS BEFORE OPERATING YOUR UNIT
1
2
To ensure the finest performance, please read this manual
9. To prevent damage by lightning, disconnect the power cord
carefully. Keep it in a safe place for future reference.
from the household AC outlet during an electrical storm.
Install your unit in a cool, dry, clean place – away from
windows, heat sources, and too much vibration, dust,
moisture or cold. Avoid sources of hum (transformers,
motors). To prevent fire or electrical shock, do not expose
to rain and water.
10. When disconnecting the power cord from the household
AC outlet, grasp the plug; do not pull the cord.
11. When moving the unit, be sure to first disconnect the
power cord from the household AC outlet, and disconnect
cords connected to other equipment.
3
4
5
Do not operate the unit upside-down. It may overheat,
possibly causing damage.
The apparatus is not disconnected from the AC power
source as long as it is connected to the wall outlet, even if
the apparatus itself is turned off.
Never open the cabinet. If a foreign object drops into the
set, contact your dealer.
Do not use force on switches, knobs or cords. When
moving the set, first turn the unit off. Then gently
disconnect the power plug and the cords connecting to
other equipment. Never pull the cord itself.
CAUTION (FOR CANADIAN CUSTOMERS)
6
7
Do not attempt to clean the unit with chemical solvents;
this might damage the finish. Use a clean, dry cloth.
TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF
PLUG TO WIDE SLOT AND FULLY INSERT.
Be sure to read the “TROUBLESHOOTING” section on common
operating errors before concluding that your unit is faulty.
THIS CLASS B DIGITAL APPARATUS MEETS ALL
REQUIREMENTS OF THE CANADIAN INTERFERENCE-
CAUSING EQUIPMENT REGULATIONS.
8. Do not place another component on top of this unit, because
to do so will discolor or damage the surface of the unit.
WARNING
To avoid electrical shock, do not open the unit. Refer
servicing to qualified personnel only.
CAUTION
Use of controls or adjustments or performance of
procedures other than those specified herein may result in
hazardous radiation exposure.
DANGER: The use of optical instrument with this product will
increase eye hazard.
DANGER
Laser Diode Properties
• Material: GaAlAs
• Wavelength: 780nm
• Emission Duration: continuous
• Laser Output: max. 44.6µW*
* This output is the value measured at a distance of about
200mm from the objective lens surface on the Optical Pick-
up Block.
Invisible laser radiation when open and interlock failed or
defeated.
Avoid direct exposure to beam.
As the laser beam used in this compact disc player is harmful
to the eyes, do not attempt to disassemble the cabinet. Refer
servicing to qualified personel only.
FCC INFORMATION (for US customers only)
1. IMPORTANT NOTICE : DO NOT MODIFY THIS UNIT!
Compliance with FCC regulations does not guarantee that
interference will not occur in all installations. If this product
is found to be the source of interference, which can be
determined by turning the unit “OFF” and “ON”, please try
to eliminate the problem by using one of the following
measures:
This product, when installed as indicated in the
instructions contained in this manual, meets FCC
requirements. Modifications not expressly approved by
Yamaha may void your authority, granted by the FCC, to
use the product.
Relocate either this product or the device that is being
affected by the interference.
2. IMPORTANT : When connecting this product to
accessories and/or another product use only high quality
shielded cables. Cable/s supplied with this product
MUST be used. Follow all installation instructions.
Failure to follow instructions could void your FCC
authorization to use this product in the USA.
Utilize power outlets that are on different branch (circuit
breaker or fuse) circuits or install AC line filter/s.
In the case of radio or TV interference, relocate/reorient the
antenna. If the antenna lead-in is 300 ohm ribbon lead,
change the lead-in to coaxial type cable.
3. NOTE : This product has been tested and found to
comply with the requirements listed in FCC Regulations,
Part 15 for Class “B” digital devices. Compliance with
these requirements provides a reasonable level of
assurance that your use of this product in a residential
environment will not result in harmful interference with
other electronic devices.
If these corrective measures do not produce satisfactory
results, please contact the local retailer authorized to
distribute this type of product. If you can not locate the
appropriate retailer, please contact Yamaha Electronics
Corp., U.S.A. 6660 Orangethorpe Ave, Buena Park, CA
90620.
This equipment generates/uses radio frequencies and, if
not installed and used according to the instructions
found in the users manual, may cause interference
harmful to the operation of other electronic devices.
The above statements apply ONLY to those products
distributed by Yamaha Corporation of America or its
subsidiaries.
3
CONNECTIONS
Before making any connections, switch OFF the power to
If the placement of this unit causes noise to other equipment,
such as a tuner, separate them from each other.
•
•
•
the unit and the amplifier or other component.
Connections should be made to the correct input terminals of
the amplifier or other component.
1
CDX-10
LINE OUT
1
To AC outlet
Connection cord
(included)
Amplifier or other component
1
CD
CDX-10
2
DIGITAL OUT
OPTICAL
To AC outlet
Optical fiber cable
(not included)
Amplifier with an optical terminal
OPTICAL
DIGITAL IN
Choose one of the ways listed below to connect this unit to your amplifier.
When the LINE OUT (analog) terminals of this
When the DIGITAL OUT (OPTICAL) terminal of
unit are used ( 1 )
this unit is used ( 2 )
Be sure that the left (“L”) and right (“R”) LINE OUT terminals
Before using this terminal, remove the terminal’s cover by
•
•
are connected to the corresponding (left and right) terminals
of the amplifier or other component.
pulling it.
Make the connection from this terminal to the optical input
terminal of an amplifier by using a commercially available
optical fiber cable.
•
Connect the “LINE OUT” terminals to the “CD” (or “AUX”)
•
terminals of the amplifier. If the amplifier does not have such
terminals, use the “TAPE PB” terminals. For additional
details concerning these connections, refer to the operation
instructions for the amplifier being used.
* Use an optical fiber cable that conforms to EIAJ
standards. Other cables might not function correctly.
Be sure to attach the terminal’s cover when this terminal is
not being used, in order to protect the terminal from dust.
•
1. When
• The LINE OUT terminals of this unit are numbered
connecting this unit with a YAMAHA amplifier or receiver
whose terminals on the rear panel are numbered as 1, 2,
3, etc., connect the LINE OUT terminals of this unit to the
input terminals numbered 1 on the rear of the amplifier or
receiver.
This terminal can also be connected to the optical input
terminal of a digital audio tape deck (DAT) etc. to record CD
onto tape directly.
•
4
IDENTIFICATION OF COMPONENTS
* ( ) indicates the page number on which the control part is best described.
FRONT PANEL
* The PLAY/PAUSE button on the main unit has both the
functions of the PLAY button and the PAUSE button on the
remote control transmitter.
* The SKIP/SEARCH buttons on the main unit have both the
functions of the SKIP buttons and the SEARCH buttons on
the remote control transmitter.
Display panel
Disc tray (p. 7)
PLAY/
POWER
PAUSE
STOP
OPEN/CLOSE button (p. 7)
SKIP/SEARCH buttons (p. 8, 9)
STOP button (p. 8)
PLAY/PAUSE button (p. 7, 8)
Remote control sensor (p. 18)
POWER switch (p. 7)
5
* ( ) indicates the page number on which the control part is best described.
REMOTE CONTROL TRANSMITTER
DIMMER button (p. 8)
CLEAR button (p. 12)
TAPE button (p. 13)
OPEN/CLOSE button (p. 7)
TIME
DIMMER
CLEAR
OPEN/
CLOSE
TIME button (p. 9)
PROG button (p. 11)
PROG
SPACE
1
TAPE
PEAK
RANDOM
+10
PEAK button (p. 16)
S/F
SPACE button (p. 9)
REPEAT
RANDOM button (p. 10)
2
5
8
3
REPEAT button (p. 10)
Numeric buttons (p. 8)
4
6
9
PAUSE button (p. 8)
7
0
SKIP
PAUSE
INDEX
PLAY
STOP
SKIP buttons (p. 8)
SEARCH buttons (p. 9)
SYNCHRO button (p. 17)
PLAY button (p. 7)
STOP button (p. 8)
SEARCH
SYNCHRO
INDEX button (p. 12)
6
This manual describes how to operate this unit by using the remote control transmitter.
To operate this unit on the front panel, use the corresponding buttons on the front panel.
BASIC OPERATION
2, 3
DIMMER
CLEAR
TIME
OPEN/
CLOSE
PROG
TAPE
PEAK
RANDOM
+10
SPACE
S/F
REPEAT
3
1
2
5
8
4
6
9
POWER
7
0
1
SKIP
PAUSE
INDEX
PLAY
STOP
4
SEARCH
SYNCHRO
1
2
Turn the power on.
3
4
Close the disc tray.
POWER
OPEN/
CLOSE
Load a disc.
Label side
upward
PLAY
OPEN/
CLOSE
Play will begin from the first track of the disc.
Disc tray
Notes
•
Display information at disc play
After closing the disc tray by pressing the OPEN/CLOSE
button, the display shows the total number of tracks and the
total recorded time of the disc for a few seconds.
1
2
TOTAL
Additionally, you can close the disc tray by pressing the
PLAY (PLAY/PAUSE) button, a numeric button or the
RANDOM button, or by pressing the front edge of the disc
tray gently. If the tray is closed in these ways, play will begin
automatically, however, the display will not show the total
number of tracks and the total recorded time of the disc.
•
Shows the track number selected or being played.
Shows the time displays. (Refer to “Selecting time
displays” on page 9.)
➀
➁
To turn off the power
Press the POWER switch again.
7
To stop play temporarily
To stop play completely
PAUSE
STOP
To resume play, press the PAUSE button again (or press the
PLAY button).
* The PLAY/PAUSE button on the front panel can also be
used to stop play temporarily or to resume play.
To play a desired track on the disc
DIRECT PLAY
Select a desired track using the numeric button.
SKIP PLAY
To play from the beginning of the track following the one now
playing
SKIP
5
To play from the beginning of the track now playing
SKIP
The selected track
number is displayed
To play from the beginning of the track before the one now
playing
SKIP
Example: To select track 25
Press
twice, then immediately press
once.
➀
➁
(twice)
10
5
These operations can also be performed when the unit is in
the pause or stop mode.
•
➀
➁
When using the SKIP buttons on the remote control
transmitter:
•
If a button is pressed and held, the track number is
continuously changed to higher numbers (or lower
numbers).
When using the SKIP/SEARCH buttons on the front panel:
Be careful not to press and hold a button, otherwise the
selected track is played forward (or backward) rapidly.
*
If a track number higher than the highest track number on
the disc is selected, the last track on the disc will be
played.
Changing brightness of the display
You can change the brightness of the display by pressing the DIMMER button.
Normal illumination
DIMMER
Slightly Dim
Dim
8
To advance or reverse play rapidly (MANUAL SEARCH)
To advance rapidly
To reverse rapidly
The sound can be heard (although slightly garbled) during
•
manual search in either direction. This is convenient for
locating a precise position within a track, or for reviewing the
contents quickly.
Manual search can also be performed while disc play is
paused, though no sound will be heard.
When using the SKIP/SEARCH buttons on the front panel:
Be careful not to release a button just after it is pressed,
otherwise the play is skipped to the beginning of the next
track or returned to the beginning of the current track.
SEARCH
•
•
(Press and hold.)
(Press and hold.)
SEARCH
Automatic spacing
If you record a disc onto tape with an insufficient time space
between tracks, the tape deck will not be able to perform blank
search operations on the tape correctly. Such a search
mistake of the deck can be prevented by pressing the auto-
SPACE button to insert spaces of about 4 seconds between
the tracks before recording.
Note
When the automatic spacing function is in effect, the display of
the total time and of the total remaining time will include each
of the 4 second non-recorded intervals placed between tracks.
To cancel the automatic spacing function
SPACE
SPACE
“SPACE” goes off
from the display.
SPACE
Selecting time displays
You can select any of the four time displays by pressing the TIME display mode-select button.
Elapsed time of the track now playing
Total remaining time on the disc
➀
➃
TOTAL
REMAIN
TIME
Remaining time of the track now playing
Total disc play time
➁
➂
TOTAL
REMAIN
Note
The remaining time
is 25 or higher.
will not be displayed if the track number
➁
9
RANDOM-SEQUENCE PLAY
You can have the unit play the tracks on a disc in a random sequence selected by the unit’s microcomputer.
Notes
To perform random-sequence play
This feature will not function during programming, or during
•
programmed play.
If the POWER is switched off when the random-sequence
play is being performed, pressing the POWER switch again
to turn the unit on will begin the random-sequence play
automatically. (This feature is useful for timer play.)
RANDOM
•
If the SKIP
button is pressed during random-sequence
play, the next randomly programmed track will be played. If
the SKIP button is pressed, play will return to the
beginning of the track now being played.
•
To cancel random-sequence play
This indication appears while the unit is mixing
up tracks.
•
•
RANDOM
STOP
Total remaining time on the disc will not be displayed during
random-sequence play.
or
REPEAT PLAY
You can play any desired track or the entire disc repeatedly by pressing the REPEAT button. The repeat play mode will change
whenever you press the REPEAT button.
SINGLE REPEAT
A single track is repeatedly played.
* This is also available in the programmed-play mode and the
random-sequence play mode.
(OFF)
(If the repeat play mode is switched off, the programmed-
play mode or the random-sequence play mode will be
resumed.)
S/F
REPEAT
SINGLE
REPEAT
FULL REPEAT
All tracks (the entire disc) are played repeatedly.
* In the programmed-play mode, all programmed tracks are
repeatedly played.
* In the random-sequence play mode, all randomly sequenced
tracks are repeatedly played in the same order.
FULL
REPEAT
10
PROGRAM PLAY
You can enjoy listening to your favorite tracks in any desired order by programming tracks. As many as 25 tracks can be
programmed in sequence.
TIME
DIMMER
OPEN/
CLOSE
TAPE
CLEAR
PEAK
RANDOM
+10
PROG
SPACE
1
2
S
/F
REPEAT
3
2
5
8
3
4
4
6
9
7
0
SKIP
PAUSE
INDEX
PLAY
STOP
SEARCH
1
SYNCHRO
1
2
Stop the unit.
3
Program a desired track by pressing the corresponding
numeric button.
STOP
5
* Repeat this operation to program more tracks. You can
select the same track again.
4
PROG
PLAY
PROGRAM
TOTAL
Flashes.
Notes
Display information during programming
In step 2, if “P-01” does not appear in the display, press the
•
TIME display mode-select button.
If, during programming, the TIME display mode-select button
•
is pressed, the program number display can be changed to
display the total time of the programmed tracks. To return to
the previous display, press the TIME display mode-select
button once again.
PROGRAM
TOTAL
The SKIP (
and
playing, but only within the range of the programmed tracks.
The SEARCH ( and ) button can be used during
) button can be used during
•
•
•
➀
playing to search all tracks, including unprogrammed tracks.
The PAUSE mode can also be programmed (one time only),
if so desired, by pressing the TAPE button instead of a
➂
➁
PROGRAM
numeric button. (In this case, “
display.)
B” is illuminated on the
TOTAL
If, for a compact disc with 25 tracks or more, track number
25 or higher is programmed, the total time will disappear
from the display.
•
Shows the program number for the track to be
programmed next.
➀
Shows the selected track number.
Shows the total time of the tracks currently programmed.
➁
➂
* If the total time becomes 100 minutes or more, the highest
position of a figure will not be displayed.
11
To stop program play
To check program data
Press the STOP button. The first programmed track number
will be displayed.
To resume play, press the PLAY button. Play will begin from
the beginning of the program.
1. If during program play, press the STOP button.
2. Press the PROG button.
3. Each time the SKIP
button is pressed, the track
numbers and sequential order of the programmed tracks
can be checked one after another. The display of the
track number can be returned (sequentially in reverse
To cancel a program sequence
order) by pressing the SKIP
button.
There are several methods, as described below.
Press the STOP button or the CLEAR button while the unit
To correct program data
•
is stopped.
Open the disc tray.
Switch off the power.
1. Follow the procedure described in “To check program
data”.
2. Display the track number to be corrected by pressing the
SKIP button.
•
•
3. Press a numeric button to select a track to replace the one
displayed. The previously programmed track will be
cleared from the memory and the new one will be
programmed.
4. After the correction has been completed, once again press
the PROG button or the PLAY button.
INDEX SEARCH
If the disc includes index numbers, play can be started from any desired index number.
DIMMER
TIME
OPEN/
CLOSE
PROG
SPACE
1
TAPE
CLEAR
PEAK
RANDOM
+10
S
/F
REPEAT
3
2
5
8
4
6
9
1, 3
2
7
0
SKIP
PAUSE
INDEX
PLAY
STOP
SEARCH
SYNCHRO
To cancel the index search function
Press the INDEX button.
1
Select a track which has index numbers.
Notes
3
Not all discs have index numbers. The index system is a
•
method for sub-dividing tracks into smaller divisions (such
as, for example, the movements within classical
symphonies) for easier location of those parts. The liner
notes with the disc usually tell if such index numbers are
included.
2
3
If an index number is selected that is higher than any index
number on that disc, play will start from the last index
number point on the disc.
For some discs, play may begin slightly prior to the actual
designated index point.
If the disc has no encoded index points, play will begin from
the start of the selected track.
The index number can be designated only while the INDEX
number display is illuminated.
•
INDEX
INDEX
•
•
•
Select the desired index number.
3
12
TRACK PROGRAMMING FOR RECORDING TO TAPE
This convenient feature can be used to program tracks on a disc for recording to tape. By only memorizing the tape’s total possible
recording time, the unit will automatically program tracks or help you to program tracks so they will fit onto the tape with the least
amount of unrecorded space remaining at each end of the tape.
Automatic tape-programming
Ⅲ
This is for recording only the tracks which best fit
DIMMER
CLEAR
TIME
OPEN/
CLOSE
onto a tape.
PROG
SPACE
1
TAPE
PEAK
RANDOM
+10
3
2
S/F
REPEAT
3
2
5
8
5
4
6
9
4
6, 7
1
7
0
SKIP
PAUSE
INDEX
PLAY
STOP
SEARCH
7
Stop the unit.
Press the REPEAT button.
1
5
STOP
S/F
REPEAT
* The unit automatically programs tracks for side A and
side B separately considering the tape’s total time.
* The peak level searching function of this unit is useful for
adjusting recording level on the tape deck. (Refer to
page 16.)
6
Begin recording on the tape deck and press the
PLAY button on this unit at the same time.
2
If desired, you can automatically insert additional time
space between tracks. (Refer to page 9.)
7
The unit will pause at the end of side A of the tape.
Turn the tape over to side B. Resume recording and, at
the same time, press the PLAY or PAUSE button on
this unit.
SPACE
SPACE
Notes
• All tracks may not be programmed if the tape’s length is not
enough. To program all tracks, use a longer tape.
• In step 5, you can check the program data for side A and
side B.
3
Enter the tape’s total possible recording time.
TAPE
➀
➁
PROGRAM
A
You can select any of four tape lengths by pressing
the TAPE button.
TOTAL
➂
TAPE
(off)
Shows the number of programmed tracks for each side in
turn just after the automatic programming is finished, and
then it is replaced by the number of the first programmed
track for side A.
➀
Shows the total time of programmed tracks for each side.
Shows the side of the tape.
➁
➂
4
Otherwise, you can also enter the tape’s total possible
recording time manually.
Example: For a C-64 tape (32 minutes on each side)
•
CD synchronized recording function can be used if your
tape deck is compatible with it. If so, in step 6 and 7, press
the SYNCHRO button and then press the PLAY button on
this unit’s remote control transmitter. Recording
4
6
+
automatically begins. (For details, refer to page 17.)
13
Manual tape-programming
This is for recording desired tracks in any desired
order onto a tape.
Ⅲ
TIME
DIMMER
CLEAR
OPEN/
CLOSE
PROG
SPACE
1
TAPE
PEAK
RANDOM
+10
4
2
S
/F
REPEAT
3
2
5
8
4
6
9
3, 5
6, 7
7
0
SKIP
PAUSE
INDEX
PLAY
STOP
SEARCH
7
SYNCHRO
1
2
Follow steps 1 – 4 on page 13.
5
Select the track numbers (to be recorded on side B) in
any desired order.
1
4
7
2
5
8
3
6
9
+ 10
0
PROG
PROGRAM
A
TOTAL
REMAIN
Flashes.
6
7
Begin recording on the tape deck and press the PLAY
button on this unit at the same time.
3
4
Program desired tracks (to be recorded on side A) in
any desired order.
The unit will pause at the end of side A of the tape.
Turn the tape over to side B. Resume recording and,
at the same time, press the PLAY or PAUSE button on
this unit.
1
4
7
2
5
8
3
6
9
+ 10
0
Notes
• If, in step 3 or 5, “E rr” appears on the display, the track
number just selected cannot be programmed because there
is not enough time remaining on the tape.
• In step 3 or 5, each time a selection is made, the track
number and the tape’s remaining time will be displayed, and
then the display will change to indicate the next program
number.
When track selection for side A is finished, press the
TAPE button.
TAPE
• CD synchronized recording function can be used if your tape
deck is compatible with it. If so, in step 6 and 7, press the
SYNCHRO button and then press the PLAY button on this
unit’s remote control transmitter. Recording automatically
begins. (For details, refer to page 17.)
A pause mode is programmed.
Notes on tape programming
To check, cancel or correct program data, refer to page 12.
* In checking the program data, note that “Pu” appears
between track numbers for side A and side B.
• This function can be used to program up to track number 24.
If the disc has more than 24 tracks, track number 25 and
thereafter will not be programmed.
•
Up to a maximum of 25 tracks can be programmed. If,
however, the PAUSE mode is inserted, it is counted as one
track.
•
14
Random sequential tape-programming
The unit will automatically program tracks in random sequential order for recording to tape.
Ⅲ
TIME
DIMMER
CLEAR
OPEN/
CLOSE
PROG
SPACE
1
TAPE
PEAK
RANDOM
+10
S
/F
REPEAT
3
2
2
5
8
4
6
9
7
0
SKIP
PAUSE
INDEX
PLAY
STOP
3, 4
SEARCH
4
SYNCHRO
Notes
Because the programmed data changes every time the
RANDOM button is pressed, the amount of time remaining
at the end of the tape also changes accordingly.
If the tape’s length is not enough, all tracks cannot be
programmed. In this case, exchange the tape for a longer
one.
•
•
•
1
2
Follow steps 1 – 4 on page 13.
RANDOM
In step 2, you can check the program data for side A and
side B.
➀
➁
* The unit will automatically program tracks for side A and
side B separately considering the tape’s total time.
PROGRAM
A
TOTAL
3
4
Begin recording on the tape deck and press the PLAY
button on this unit at the same time.
➂
Shows the number of programmed tracks for each side in
turn just after the automatic programming is finished, and
then it is replaced by the number of the first programmed
track for side A.
➀
The unit will pause at the end of side A of the tape.
Turn the tape over to side B. Resume recording and, at
the same time, press the PLAY or PAUSE button on
this unit.
Shows the total time of programmed tracks for each side.
Shows the side of the tape.
➁
➂
•
CD synchronized recording function can be used if your
tape deck is compatible with it. If so, in step 3 and 4, press
the SYNCHRO button and then press the PLAY button on
this unit’s remote control transmitter. Recording
automatically begins. (For details, refer to page 17.)
15
Automatic searching for the peak level on a disc
This convenient feature automatically searches a disc for a part where the source level peaks, and next plays the part repeatedly.
For recording to tape, this feature is very helpful to adjust the recording level on the tape deck.
DIMMER
CLEAR
TIME
OPEN/
CLOSE
PROG
SPACE
1
TAPE
PEAK
RANDOM
+10
2
1
S
/F
REPEAT
3
2
5
8
4
6
9
7
0
SKIP
PAUSE
INDEX
PLAY
STOP
SEARCH
SYNCHRO
To cancel this function
Press the STOP button. (Some other buttons can also be
used to cancel this function.)
1
2
Stop the unit.
STOP
Notes
Even if the peak level search is performed twice or more on
•
the same disc, the same part will not be always selected,
because this unit will search for the peak level among parts
on the disc that are randomly selected by the internal
microcomputer.
In the program play mode, this feature will function among
•
the programmed tracks only. If program play is being
performed, first press the STOP button, and then press the
PEAK button. If program play is not being performed, only
press the PEAK button.
PEAK
PEAK
The peak level search is performed on the disc.
PEAK
REPEAT
PEAK
REPEAT
Next, the part where the source level peaks is repeatedly
played.
Adjust the recording level on the tape deck listening to
this sound.
16
CD SYNCHRONIZED RECORDING
This unit can make a tape deck’s recording synchronized with CD play automatically. With this function, you can record a CD on
tape very easily and more precisely.
This recording method needs a YAMAHA tape deck compatible with this function. (Refer to the tape deck’s operation manual to
know whether it is compatible or not.)
* This unit and the tape deck must be placed close to each other so that both of them can receive the signals from this unit’s
remote control transmitter at the same time.
TIME
DIMMER
CLEAR
OPEN/
CLOSE
1
PROG
SPACE
1
TAPE
PEAK
RANDOM
+10
S
/F
REPEAT
3
2
5
8
4
6
9
4
5
7
0
SKIP
PAUSE
INDEX
PLAY
STOP
4
3
SEARCH
SYNCHRO
1
Load the disc.
4
If necessary, select a desired track.
SKIP
5
OPEN/
CLOSE
or
5
6
2
3
Load a tape on the tape deck.
PLAY
*
The peak level search function of this unit is useful
for adjusting recording level on the tape deck. (Refer
to page 16.)
Both CD play and tape deck recording begin.
* CD play begins a little later than recording.
SYNCHRO
If you want to stop recording temporarily and restart
recording from a desired track, follow steps 3–5 again.
To cancel this function
Press the STOP button.
This unit enters into the pause mode, and the tape deck
enters into the REC/PAUSE mode.
Notes
* In this mode, the time display on this unit flashes on and
off.
To finish or stop the recording, make proper operations on
•
the tape deck.
Programmed sequence of tracks can also be recorded with
this function, instead of recording an entire disc. (Refer to
page 11–12 for the programming procedure.)
•
This function can also be used together with the automatic
tape-programming function. (Refer to page 13–15.)
•
17
NOTES ABOUT THE REMOTE CONTROL TRANSMITTER
Battery installation
Remote control transmitter operation range
1
3
2
Remote control
sensor
Within approximately
6m (19.7 feet)
Battery replacement
If you find that the remote control transmitter must be used
closer to the main unit, the batteries are weak. Replace both
batteries with new ones.
Notes
Use only AA, R6, UM-3 batteries for replacement.
Be sure the polarities are correct. (See the illustration inside
the battery compartment.)
•
•
Notes
Remove the batteries if the remote control transmitter will not
be used for an extended period of time.
There should be no large obstacles between the remote
control transmitter and the main unit.
•
•
If batteries leak, dispose of them immediately. Avoid
If the remote control sensor is directly illuminated by strong
lighting (especially an inverter type of fluorescent lamp etc.),
it might cause the remote control transmitter not to work
correctly. In this case, reposition the main unit to avoid direct
lighting.
•
•
touching the leaked material or letting it come in contact with
clothing, etc. Clean the battery compartment thoroughly
before installing new batteries.
NOTES ABOUT HANDLING COMPACT DISCS
This compact disc player is designed only for playing
Compact discs are not affected by small particles of dust or
•
•
fingerprints on their playing surface, but even so they should
be kept clean. Wipe by using a clean, dry cloth. Do not
wipe with a circular motion; wipe straight outward from the
center.
compact discs bearing the
mark. Never attempt to load
any other type of disc into the unit.
The unit will also play 8-cm (3-inch) compact discs.
To remove a disc from its storage case, open the case and
then press down at the center; with a finger through the
center hole and the outer edges held as shown in the
illustration, lift the disc out carefully.
•
Do not try to clean the disc’s surface by using any type of
disc cleaner, record spray, anti-static spray or liquid, or any
other chemical-based liquid, because such substances might
irreparably damage the disc’s surface.
•
•
Always handle the disc with care so that its surface is not
scratched.
•
•
Do not expose discs to direct sunlight, high temperature or
high humidity for a long period of time, because these might
warp or otherwise damage the disc.
No!
Compact discs are not subjected to wear during play, but
damage to the disc surface when the disc is being handled
can adversely affect the disc’s play.
To play a 8-cm (3-inch) CD
Place it in the inner recessed area of the disc tray. Do not put
a normal (12-cm/5-inch) CD on top of a 8-cm CD.
18
TROUBLESHOOTING
If the unit fails to operate normally, check the following points to determine whether the fault can be corrected by the simple
measures suggested. If it cannot be corrected, or if the fault is not listed in the SYMPTOM column, disconnect the power cord and
contact your authorized YAMAHA dealer or service center for help.
SYMPTOM
PROBABLE CAUSE
REMEDY
The player does not switch ON when
the POWER switch is pressed.
The power cord is not connected or not
completely connected.
Securely connect the power cord.
The disc tray does not close
completely.
A foreign object is obstructing the tray.
Carefully check the disc tray and remove
the foreign object.
Play does not begin.
The disc is damaged.
Check the disc carefully; replace it if
necessary.
There is moisture on the laser pickup.
Wait 20 to 30 minutes after switching the
unit ON before trying to play a disc.
The disc has been loaded upside down.
The disc is dirty.
Reload the disc with the label side up.
Clean the disc.
Play is delayed, or begins at the
wrong place.
The disc may be scratched or damaged.
Check the disc carefully; replace it if
necessary.
No sound.
Improper output cable connections.
Improper amplifier operation.
Connect the cables properly. If the
problem persists, the cables may be
defective.
Set the amplifier controls to the correct
input selection.
Sound “skips”.
Sound “hums”.
The player is being subjected to
vibrations or impacts.
Relocate the player.
The disc is dirty.
Clean the disc.
Improper cable connections.
Securely connect the audio cables. If the
problem persists, the cables may be
defective.
Noise from a nearby tuner.
The tuner is too close to the player.
The disc may be warped.
Move the tuner and player farther apart.
Replace the disc.
Noise from inside of the disc tray.
The remote control transmitter does
not work.
The batteries of this remote control
transmitter are too weak.
Replace the batteries with new ones.
Direct sunlight or lighting (of an inverter
type of flourescent lamp etc.) is striking
the remote control sensor of the main
unit.
Change position of the main unit.
SPECIFICATIONS
AUDIO SECTION
GENERAL
Frequency response ....................... 2 Hz
מ 20 kHz, ע 0.3 dB Harmonic distortion + noise ....................... 0.0022% (1 kHz)
S/N ratio ........................................................................ 118 dB
Dynamic range ............................................................... 98 dB
Wow & flutter ................................................... Unmeasurable
Output voltage ......................................................... 2.0
ע 0.5V Power requirements ............................................ 120V, 60 Hz
Power consumption ........................................................ 15W
Dimensions (W x H x D) ........................ 280 x 82.5 x 354 mm
(11” x 3-1/4” x 13-15/16”)
Weight ....................................................... 3.8 kg (8 lbs. 6 oz.)
Accessories ................................................... Connection cord
Remote control transmitter
Batteries (size AA, R6, UM-3)
Please note that all specifications are subject to change
without notice.
19
YAMAHA ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A.
YAMAHA CANADA MUSIC LTD. 135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA
YAMAHA ELECTRONIK EUROPA G.m.b.H. SIEMENSSTR. 22-34, D-25462 RELLINGEN BEI HAMBURG, F.R. OF GERMANY
YAMAHA ELECTRONIQUE FRANCE S.A. RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE
YAMAHA ELECTRONICS (UK) LTD. YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD1 7JS, ENGLAND
YAMAHA SCANDINAVIA A.B.
YAMAHA MUSIC AUSTRALIA PTY, LTD. 17-33 MARKET ST., SOUTH MELBOURNE, 3205 VIC., AUSTRALIA
J
A
WETTERGRENS GATA 1, BOX 30053, 400 43 VÄSTRA FRÖLUNDA, SWEDEN
0000000
|