Model No. 831.15711.0
Serial No.
Write the serial number in the
space above for reference.
WEIGHT BENCH EXERCISER
User’s Manual
Serial Number Decal (under seat)
• Assembly
• Adjustment
• Part List and Drawing
CAUTION
Read all precautions and instruc-
tions in this manual before using
this equipment. Save this manu-
al for future reference.
Sears, Roebuck and Co., Hoffman Estates, IL 60179
IMPORTANT PRECAUTIONS
WARNING:
To reduce the risk of serious injury, read the following important precau-
tions before using the weight bench.
1. Read all instructions in this manual and all
warnings on the weight bench before using
the weight bench. Use the weight bench only
as described in this manual.
11. The weight bench is designed to support a
maximum user weight of 300 lbs. (136 kg)
and a maximum total weight of 510 lbs. (231
kg). Do not place more than 210 lbs. (95 kg),
including a barbell and weights, on the
weight rests. Do not place more than 130 lbs.
(59 kg) on the leg lever or the weight car-
riage. Note: The weight bench does not
include a barbell or weights.
2. It is the responsibility of the owner to ensure
that all users of the weight bench are ade-
quately informed of all precautions.
3. The weight bench is intended for home use
only. Do not use the weight bench in any
commercial, rental, or institutional setting.
12. Always make sure that there is an equal
amount of weight on each side of the barbell
when you are using it. Always keep some
weight on both ends of the barbell when
adding or removing weights to prevent the
barbell from tipping.
4. Keep the weight bench indoors, away from
moisture and dust. Place the weight bench
on a level surface, with a mat beneath it to
protect the floor or carpet. Make sure that
there is enough clearance around the weight
bench to mount, dismount, and use the
weight bench.
13. When you are using the leg lever, place a
barbell with the same amount of weight on
the weight rests to balance the weight bench.
5. Inspect and properly tighten all parts regular- 14. When you put weight on the weight rests,
ly. Replace any worn parts immediately.
make sure that you put at least 10 lbs. (5 kg)
on the leg lever to balance the weight bench.
6. Keep children under age 12 and pets away
from the weight bench at all times.
15. Make sure that the adjustment pin and the
weight rest knobs are inserted completely
and tightened into the uprights before begin-
ning any exercise.
7. Keep hands and feet away from moving parts.
8. Always wear athletic shoes for foot protec-
tion while exercising.
16. Always remove the curl post and the lat
tower from the front leg before using the leg
lever.
9. Always exercise with a partner. When you
are performing bench press exercises, your
partner should stand behind you to catch the 17. If you feel pain or dizziness at any time while
barbell if you cannot complete a repetition.
exercising, stop immediately and cool down.
10. Do not sit on the top end of the backrest;
this will cause the weight bench to tip.
WARNING:
Before beginning this or any exercise program, consult your physician. This
is especially important for persons over the age of 35 or persons with pre-existing health problems.
Read all instructions before using. Sears assumes no responsibility for personal injury or property
damage sustained by or through the use of this product.
3
BEFORE YOU BEGIN
Thank you for selecting the versatile WEIDER® PRO
reading this manual, call 1-800-4-MY-HOME®
265 weight bench. The weight bench offers an impres- (1-800-469-4663). To help us assist you, please note
sive array of weight stations designed to develop
every major muscle group of the body. Whether your
goal is to tone your body, build dramatic muscle size
and strength, or improve your cardiovascular system,
the weight bench will help you to achieve the specific
results you want.
the product model number and serial number before
calling. The model number is 831.15711.0. The serial
number can be found on a decal attached to the
weight bench (see the front cover of this manual for
the location of the decal).
Before reading further, please review the drawing
below and familiarize yourself with the parts that are
labeled.
For your benefit, read this manual carefully before
using the weight bench. If you have questions after
ASSEMBLED DIMENSIONS:
Height: 79 in. (201 cm)
Width: 40 in. (102 cm)
Depth: 70 in. (178 cm)
Lat Bar
Lat Tower
Weight Rest
Backrest
Weight Rest Knob
Upright
Weight Carriage
Storage Tube
Seat
Leg Lever
Backrest Bracket
Weight Tube
4
PART IDENTIFICATION CHART
Refer to the drawings below to identify small parts used in assembly. The number in parentheses by each draw-
ing is the key number of the part, from the PART LIST on page 18. Important: Some parts may have been
pre-assembled for shipping purposes. If you cannot find a part in the parts bags, check to see if it has
been pre-assembled. If a part is missing, call 1-877-992-5999.
M10 x 81mm Bolt (41)
M10 Nylon Locknut (43)
M10 x 75mm Bolt (42)
M8 Nylon Locknut (55)
M10 x 68mm Bolt (54)
M6 Nylon Locknut (51)
M10 x 65mm Bolt (40)
M10 x 60mm Bolt (47)
M10 Washer (44)
M8 x 58mm Bolt (52)
M8 Washer (56)
M6 x 40mm Bolt (49)
M6 Washer (48)
M10 x 19mm Bolt (53)
M4 x 16mm Screw (45)
M6 x 16mm Screw (39)
5
ASSEMBLY
• Tighten all parts as you assemble them, unless
instructed to do otherwise.
Make Assembly Easier
Everything in this manual is designed to ensure
that the weight bench can be assembled suc-
cessfully by almost anyone. However, the weight
bench has many parts and the assembly
process will take time. By setting aside plenty of
time, assembly will go smoothly.
• As you assemble the weight bench, make sure all
parts are oriented as shown in the drawings.
• For help identifying small parts, use the Part
Identification Chart.
The included grease and the following tools (not
included) may be required for assembly:
Before beginning assembly, carefully read the
following information and instructions:
• Two adjustable wrenches
• One rubber mallet
• Assembly requires two people.
• One standard screwdriver
• Because of its weight and size, the weight bench
should be assembled in the location where it will
be used. Make sure that there is enough clear-
ance to walk around the weight bench as you
assemble it.
• One Phillips screwdriver
Assembly will be more convenient if you have a
socket set, a set of open-end or closed-end
wrenches, or a set of ratchet wrenches.
• Place all parts in a cleared area and remove the
packing materials. Do not dispose of the packing
materials until assembly is completed.
1.
1
Before assembling the weight bench, make
sure that that you have read and under-
stand the information in the box above.
5
Lift the Weight Rest (7) in the Left Upright (6) and
secure it with a Weight Rest Knob (23).
18
7
4
Attach the Crossbar (4) to the Left Upright (6)
with a Right Joint Plate (18), a Left Joint Plate
(59), four M10 x 75mm Bolts (42), and four M10
Nylon Locknuts (43). Do not tighten the Nylon
Locknuts yet.
23
43
59
59
43
Attach the Crossbar (4) to the Right Upright
(5) in the same manner.
42
6
18
6
2. Attach the Bench Frame (1) to the Front Leg (2)
with two M10 x 65mm Bolts (40), two M10
Washers (44), and two M10 Nylon Locknuts (43).
Do not tighten the Nylon Locknuts yet.
2
40
1
44
40
43
2
3. Attach the Bench Frame (1) to the Crossbar (4)
with two M10 x 81mm Bolts (41) and two M10
Nylon Locknuts (43).
3
4
Tighten the M10 Nylon Locknuts (43) used in
steps 1 through 3.
43
41
41
43
1
4. Attach the Weight Tube (16) inside the Leg Lever
(3) with an M8 x 58mm Bolt (52), two M8
Washers (56), a 10mm Spacer (32), and an M8
Nylon Locknut (55).
4
2
3
Press the 25mm Round Angled Cap (28) onto the
Weight Tube (16).
Grease
55
56
28
54
32
Grease an M10 x 68mm Bolt (54). Attach the Leg
Lever (3) with the Bolt and an M10 Nylon Locknut
(43). Do not overtighten the Nylon Locknut;
the Leg Lever must pivot easily.
56
16
52
48
5. Orient the Backrest Frames (12) with the indicat-
ed tubes in the position shown. Attach the
Backrest Frames to the Backrest Bracket (10)
with four M6 x 40mm Bolts (49), four M6 Washers
(48), and four M6 Nylon Locknuts (51). Do not
tighten the Nylon Locknuts yet.
5
49
12
12
48
48
49
Tubes
48
51
51
10
7
6. Attach the Backrest (13) to the Backrest Frames
(12) with four M6 x 40mm Bolts (49) and four M6
Washers (48). Do not tighten the Bolts yet.
6
13
12
48
12
48
48
49
49
7. Insert the Backrest Bracket (10) through the
Bench Frame (1).
7
Grease an M10 x 168mm Bolt (50). Attach the
Backrest Frames (12) to the Bench Frame (1)
with the Bolt and an M10 Nylon Locknut (43). Do
not overtighten the Nylon Locknut; the
Backrest Frames must pivot easily.
12
Attach the Adjustment Pin (25) to the Bench
Frame (1) with an M4 x 16mm Screw (45).
Engage the Pin into the Bench Frame and the
Backrest Bracket (10).
10
43
25
Tighten the M6 x 40mm Bolts (49) and M6
Nylon Locknuts (51) used in steps 5 and 6.
45
1
50
8. Attach the Seat (14) to the Bench Frame (1) with
four M6 x 16mm Screws (39).
8
14
1
39
8
9. Insert a Pad Tube (19) into the Leg Lever (3).
Slide two Foam Pads (20) onto the Pad Tube.
9
2
19
19
3
Repeat this step with the other two Pad Tubes
(19) and the Leg Lever (3) and Front Leg (2).
20
20
19
10. Attach the Curl Pad (15) to the Curl Post (11) with
two M6 x 16mm Screws (39).
10
15
11
39
11. Route the Lat Cable (35) through the Lat Tower
(8) and over the Pulley (38). Make sure that the
Cable is under the lat bar rest. Attach the Pulley
inside the Lat Tower with an M10 x 60mm Bolt
(47), two M10 Washers (44), two 10mm Large
Spacers (31), and an M10 Nylon Locknut (43).
11
Lat Bar
Rest
43
44
31
35
44
47
38
31
8
12. Insert an M10 x 19mm Bolt (53) into the bracket
on the Weight Carriage (9).
12
8
Slide the Weight Carriage (9) onto the Lat Tower
(8). Make sure that the bracket on the Weight
Carriage and the lat bar rest on the Lat Tower
(see step 11) are on opposite sides of the Lat
Tower. Attach the Lat Cable (35) to the M10 x
19mm Bolt (53) with an M10 Nylon Locknut (43).
35
43
53
Bracket
13. Make sure that all parts are properly tightened
before the weight bench is used. The use of all
remaining parts will be explained in ADJUST-
MENT on page 10.
9
9
ADJUSTMENT
This section explains how to adjust the weight bench. See the EXERCISE GUIDELINES on page 12 for impor-
tant information about how to get the most benefit from your exercise program. Also, refer to the accompanying
exercise guide to see the correct form for each exercise.
Make sure all parts are properly tightened each time the weight bench is used. Replace any worn parts immediate-
ly. The weight bench can be cleaned with a damp cloth and a mild, non-abrasive detergent. Do not use solvents.
ADJUSTING THE BACKREST
The Backrest (13) can be used in a decline position,
a level position, or an incline position. To use the
Backrest in the decline position, remove the
Adjustment Pin (25) and lay the Backrest on the
Crossbar (4).
13
4
To use the Backrest (13) in the level or inclined posi-
tion, lift the Backrest and insert the Adjustment Pin
(25) through the Bench Frame (1) and a hole in the
Backrest Bracket (10).
1
25
Adjustment
Holes
10
ADDING WEIGHT
Weight
To use the Weight Carriage (9) or the Leg Lever (3),
slide the desired weights (not included) onto the
Weight Carriage or the Weight Tube (16). Secure the
weights on the Weight Carriage with the Spring Clips
(36). Unused weights can be stored on the tubes on
the Uprights (not shown).
9
3
36
WARNING:
Do not place more than
130 lbs. (59 kg) on the Weight Carriage (9) or
Weight Tube (16).
16
ADJUSTING THE WEIGHT RESTS
To change the height of the Weight Rests (7), remove
the Weight Rest Knobs (23). Position the Weight
Rests to the desired height in the Uprights (5, 6) and
secure them with the Weight Rest Knobs.
7
23
WARNING:
Always set both Weight
5
Rests (7) at the same height. Make sure that the
Weight Rest Knobs (23) are inserted into both
the Uprights (5, 6) and the Weight Rests.
7
6
23
10
ATTACHING THE CURL PAD
For some exercises, the Curl Pad (15) must be
attached to the weight bench. Remove the 45mm
Thick Square Inner Cap (57) from the Front Leg (2).
8
Insert the Curl Post (11) into the Front Leg (2). Align
one of the adjustment holes in the Curl Post with the
adjustment hole in the Front Leg. Fully tighten the
Curl Knob (34) into the Front Leg.
15
The Lat Tower (8) can be attached in the same way.
Note: When the Curl Pad (15) or Lat Tower (8) is not
in use, the 45mm Thick Square Inner Cap (57) should
be inserted into the Front Leg (2).
11
57
34
2
ATTACHING THE LAT BAR
Attach the Lat Bar (17) to the Lat Cable (35) with a
Cable Clip (37). Remove the Lat Bar when performing
an exercise that does not require it.
35
37
17
11
EXERCISE GUIDELINES
THE FOUR BASIC TYPES OF WORKOUTS
PERSONALIZING YOUR EXERCISE PROGRAM
Muscle Building
To increase the size and strength of your muscles,
Determining the appropriate length of time for each
workout, and the number of repetitions or sets to com-
push them close to their maximum capacity. Your mus- plete, is an individual matter. Avoid overdoing it during
cles will continually adapt and grow as you progres-
sively increase the intensity of your exercise. You can
adjust the intensity level of an individual exercise in
two ways:
• by changing the amount of resistance used
• by changing the number of repetitions or sets per-
formed. (A “repetition” is one complete cycle of an
exercise, such as one sit-up. A “set” is a series of
repetitions.)
the first few months of your exercise program.
Progress at your own pace and be sensitive to your
body’s signals. If you experience pain or dizziness
while exercising, stop immediately and cool down.
Find out what is wrong before continuing. Remember
that adequate rest and a proper diet are important fac-
tors in any exercise program.
WARMING UP
The proper amount of resistance for each exercise
depends upon the individual user. You must gauge
your limits and select the amount of resistance that is
Begin each workout with 5 to 10 minutes of stretching
and light exercise to warm up. Warming up prepares
your body for more strenuous exercise by increasing
right for you. Begin with 3 sets of 8 repetitions for each circulation, raising your body temperature and deliver-
exercise you perform. Rest for 3 minutes after each
set. When you can complete 3 sets of 12 repetitions
without difficulty, increase the amount of resistance.
ing more oxygen to your muscles.
WORKING OUT
Toning
Each workout should include 6 to 10 different exercis-
You can tone your muscles by pushing them to a mod- es. Select exercises for every major muscle group,
erate percentage of their capacity. Select a moderate
amount of resistance and increase the number of rep-
etitions in each set. Complete as many sets of 15 to
20 repetitions as possible without discomfort. Rest for
1 minute after each set. Work your muscles by com-
emphasizing areas that you want to develop most. To
give balance and variety to your workouts, vary the
exercises from workout to workout.
Schedule your workouts for the time of day when your
pleting more sets rather than by using high amounts of energy level is the highest. Each workout should be
resistance.
followed by at least one day of rest. Once you find the
schedule that is right for you, stick with it.
Weight Loss
To lose weight, use a low amount of resistance and
increase the number of repetitions in each set.
Exercise for 20 to 30 minutes, resting for a maximum
of 30 seconds between sets.
EXERCISE FORM
Maintaining proper form is an essential part of an
effective exercise program. This requires moving
through the full range of motion for each exercise, and
moving only the appropriate parts of the body.
Cross Training
Cross training is an efficient way to get a complete and Exercising in an uncontrolled manner will leave you
well-balanced fitness program. An example of a bal-
anced program is:
• Plan strength training workouts on Monday,
Wednesday, and Friday.
• Plan 20 to 30 minutes of aerobic exercise, such as
running on a treadmill or riding on an exercise cycle,
on Tuesday and Thursday.
feeling exhausted. On the exercise guide accompany-
ing this manual you will find photographs showing the
correct form for several exercises, and a list of the
muscles affected. Refer to the muscle chart on the
next page to find the names of the muscles.
The repetitions in each set should be performed
• Rest from both strength training and aerobic exercise smoothly and without pausing. The exertion stage of
for at least one full day each week to give your body
time to regenerate.
each repetition should last about half as long as the
return stage. Proper breathing is important. Exhale
during the exertion stage of each repetition and inhale
during the return stroke. Never hold your breath.
The combination of strength training and aerobic exer-
cise will reshape and strengthen your body, plus devel-
op your heart and lungs.
12
Rest for a short period of time after each set. The
ideal resting periods are:
• Rest for three minutes after each set for a muscle
building workout.
slowly as you stretch and do not bounce. Ease into
each stretch gradually and go only as far as you can
without strain. Stretching at the end of each workout
is an effective way to increase flexibility.
• Rest for one minute after each set for a toning work-
out.
STAYING MOTIVATED
• Rest for 30 seconds after each set for a weight loss
workout.
Plan to spend the first couple of weeks familiarizing
yourself with the equipment and learning the proper
form for each exercise.
For motivation, keep a record of each workout. The
chart on pages 14 and 15 of this manual can be pho-
tocopied and used to schedule and record your work-
outs. List the date, the exercises performed, the resist-
ance used, and the numbers of sets and repetitions
completed. Record your weight and key body meas-
urements at the end of every month. Remember, the
key to achieving the greatest results is to make exer-
cise a regular and enjoyable part of your everyday life.
COOLING DOWN
End each workout with 5 to 10 minutes of stretching.
Include stretches for both your arms and legs. Move
MUSCLE CHART
O
A. Sternomastoid (neck)
A
B. Pectoralis Major (chest)
C. Biceps (front of arm)
D. Obliques (waist)
P
L
Q
B
E. Brachioradials (forearm)
F. Hip Flexors (upper thigh)
G. Abductor (outer thigh)
H. Quadriceps (front of thigh)
I. Sartorius (front of thigh)
J. Tibialis Anterior (front of calf)
K. Soleus (front of calf)
R
S
C
D
E
T
F
M
N
U
L. Anterior Deltoid (shoulder)
M. Rectus Abdominus (stomach)
N. Adductor (inner thigh)
G
H
I
V
O. Trapezius (upper back)
P. Rhomboideus (upper back)
Q. Posterior Deltoid (shoulder)
R. Triceps (back of arm)
S. Latissimus Dorsi (mid back)
T. Spinae Erectors (lower back)
U. Gluteus Medius (hip)
W
X
J
K
V. Gluteus Maximus (buttocks)
W. Hamstring (back of leg)
X. Gastrocnemius (back of calf)
13
EXERCISE
WEIGHT
WEIGHT
WEIGHT
SETS
SETS
SETS
REPS
REPS
REPS
MONDAY
Date:
/
/
AEROBIC EXERCISE
EXERCISE
TUESDAY
Date:
/
/
WEDNESDAY
Date:
/
/
AEROBIC EXERCISE
EXERCISE
THURSDAY
Date:
/
/
FRIDAY
Date:
/
/
Make photocopies of this page for scheduling and recording your workouts.
14
EXERCISE
WEIGHT
WEIGHT
WEIGHT
SETS
SETS
SETS
REPS
REPS
REPS
MONDAY
Date:
/
/
AEROBIC EXERCISE
EXERCISE
TUESDAY
Date:
/
/
WEDNESDAY
Date:
/
/
AEROBIC EXERCISE
EXERCISE
THURSDAY
Date:
/
/
FRIDAY
Date:
/
/
Make photocopies of this page for scheduling and recording your workouts.
15
NOTES
16
NOTES
17
PART LIST—Model No. 831.15711.0
R0407A
Key No. Qty.
Description
Key No. Qty.
Description
1
2
3
4
5
6
7
8
1
1
1
1
1
1
2
1
1
1
1
2
1
1
1
1
1
2
3
6
2
2
2
2
1
3
2
1
4
2
2
Bench Frame
Front Leg
Leg Lever
Crossbar
Right Upright
Left Upright
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
1
4
1
1
2
1
1
6
2
2
8
16
4
5
6
1
8
8
1
4
1
1
1
1
2
2
1
2
-
10mm Spacer
25mm Round Inner Cap
Curl Knob
Lat Cable
Spring Clip
Cable Clip
Pulley
Weight Rest
Lat Tower
M6 x 16mm Screw
M10 x 65mm Bolt
M10 x 81mm Bolt
M10 x 75mm Bolt
M10 Nylon Locknut
M10 Washer
M4 x 16mm Screw
19mm Round Inner Cap
M10 x 60mm Bolt
M6 Washer
M6 x 40mm Bolt
M10 x 168mm Bolt
M6 Nylon Locknut
M8 x 58mm Bolt
M10 x 19mm Bolt
M10 x 68mm Bolt
M8 Nylon Locknut
M8 Washer
9
Weight Carriage
Backrest Bracket
Curl Post
Backrest Frame
Backrest
Seat
Curl Pad
Weight Tube
Lat Bar
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
Right Joint Plate
Pad Tube
Foam Pad
Weight Rest Cap
Square Bushing
Weight Rest Knob
Lat Tower Bushing
Adjustment Pin
45mm Square Inner Cap
25mm x 51mm Inner Cap
25mm Round Angled Cap
25mm Square Inner Cap
Lat Handgrip
45mm Thick Square Inner Cap
25mm Thin Round Inner Cap
Left Joint Plate
User’s Manual
Exercise Guide
*
*
*
-
-
10mm Large Spacer
Grease Packet
Note: Specifications are subject to change without notice. See the back cover of this manual for information
about ordering replacement parts. If a part is missing, call 1-877-992-5999. *These parts are not illustrated.
18
EXPLODED DRAWING—Model No. 831.15711.0
R0407A
13
30
17
29
7
12
49
57
31
30
47
45
43
44
48
48
48
43
48
45
35
38
48
21
22
31
29
44
49
48
7
50
23
49
51
33
45
51
5
37
45
10
8
43
4
21
22
36
18
23
43
59
42
35
43
24
53
33
33
6
33
59
14
42
18
9
43
15
41
45
24
40
41
25
57
34
1
43
26
46
20
40
3
39
19
43
26
54
11
39
20
44
27
28
2
32
39
19
55
56
20
58
27
56
20
16
52
26
46
19
Get it fixed, at your home or ours!
Your Home
For repair—in your home—of all major brand appliances, lawn and garden equipment,
or heating and cooling systems, no matter who made it, no matter who sold it!
For the replacement parts, accessories, and user’s manuals that you need to do-it-yourself.
For Sears professional installation of home appliances
and items like garage door openers and water heaters.
1-800-4-MY-HOME® (1-800-469-4663)
Call anytime, day or night (U.S.A. and Canada)
Our Home
For repair of carry-in items like vacuums, lawn equipment,
and electronics, call or go on-line for the location of your nearest
Sears Parts & Repair Center.
1-800-488-1222 Call anytime, day or night (U.S.A. only)
To purchase a protection agreement (U.S.A.)
or maintenance agreement (Canada) on a product serviced by Sears:
1-800-827-6655 (U.S.A.)
1-800-361-6665 (Canada)
Para pedir servicio de reparación a domicilio, y para ordenar piezas:
1-888-SU-HOGAR® (1-888-784-6427)
® Registered Trademark / TM Trademark / SM Service Mark of Sears Brands, LLC
® Marca Registrada / TM Marca de Fábrica / SM Marca de Servicio de Sears Brands, LLC
90-DAY FULL WARRANTY
If this Sears WEIGHT BENCH EXERCISER fails due to a defect in material or workmanship within 90
days of the date of purchase, call 1-800-4-MY-HOME® (1-800-469-4663) to arrange for free repair (or
replacement if repair proves impossible).
This warranty does not apply when the WEIGHT BENCH EXERCISER is used commercially or for rental
purposes. This warranty gives you specific legal rights, and you may also have other rights which vary
from state to state.
Sears, Roebuck and Co., Hoffman Estates, IL 60179
Part No. 252431 R0407A
Printed in China © 2007 ICON IP, Inc.
|